- Hand Tools,Combination
- Number of Pieces:
- Brand Name:
- magic PDR
- Model Number:
- car dent repair tool kit
level tools are made by USA chromium alloy material,super-hard, excellent elasticity,it could repair aluminum skin car absolutely .It is unbending after run over by a car ,There are 6 layers of electroplating and it is bright white,it is very comfortable to use with your hands,if you want to know about Hardness and elasticity with this tool ,you can contact us ,we will send you some video about it .
Repair effect is perfectly!!!
This tools with a ''knock&pull'' type hammer, advantage, if meet these dents as larger as basin,at first we can smooth these dents with this tool ;second ,we use the lever tool repair the uneven places ,so all is ok .It is used more convenient and fast .
- Make these dents clean.
- Make the hot melt glue sticks slip into the hot melt adhesive robs, let the glue stick warm-up 5 minutes.
- Rubber mat's (cushion screw) size (three kinds of size) is consistent with the size of the dent, the bigger dent needs to the bigger rubber mat (Note: bigger rubber mat could make the pull bigger)
- Let the hot melt glue gun of the fully covered the bottom of the rubber pad, make sure that the 4 holes are covered fully.
- Immediately make the rubber pads in the middle part of dent ,don't move it until self-adhesive on its own it, make the glue dry for about 3-5 minutes, so that the glue would stick firmly.
- make the screw which upon of the rubber pad through the tension bridge central hole, Tighten the knob until the pad bursts a voice "wave" out of the car body, the pull bridge is designed with elastic traction, allow pull bridge arc are drawn to the maximum tension .
- Repeat these steps until the dents are smooth.
- If the metal is generated high convex points, use this way: first, use your thumb to press the area until the flat high surface are calm. If by this way, it is not good, please use three kinds of size of dimension combination tools, first, light pressure high until it is recovered .You can repeat these steps.
- Sometimes the adhesive residue on the car body, you can deal with it carefully by your hands. Protect your eyes with the magic dent recovery; be careful not to be scalded with hot melt adhesive.
1. The ideal temperature for repair dent is 65-85 degrees (18-29 Celsius).
2. If the car body's temperature is cold, heat it by hair dryer.
3. Preheating it more than 10 minutes, hot melt glue gun of the glue will overheat ,it causes too sticky, so that traction is too big or pull knob is screwed down to the lowest bridge are still unable to make the rubber pad "wave" from the body.
4. If you accidentally let pad in the body for more than 8 minutes, and to minimize Tension Bridge (pad could not "wave" from car body), simply Pull Bridge gently to the left or right pressure can be removed.
5. If the dent was not completely repaired, repeat the above procedure until you get the results you want. (Note: not the entire dent can be 100% are repaired).
6. If the body of a scratch or paint off, use the hot melt adhesive traction dent may lead to more paint off, if the residue in the body or the rubber pad, you can remove all the glue with the amount of alcohol.
7. repair the dents which more than the size of our the rubber pad , try other techniques:
8. About the PDR tools, it looks like simply, but don't worry about follow descriptions, ha-ha!!!!
9. Auto depression repairing, it is the appearance of the vehicle above the pit with special tool in leveling not paint not sheet metal case, and the original as like as two peas. How can we achieve this effect? At first everyone wondering, chuck depression may be a major force in repair, or vacuum or magnet. In fact, not like that. At the very least, by now it's only a dream, because vacuum suction or high strength magnet sucker is impossible to sag adsorption. This is not absolute. For example, special parts could be gently pushed out, sucking it out with a sucker could . But such depression 1000 which may not have one. This tool made by the United States chromium alloy with high frequency quenching equipment after heating bent into different curved, long short coarse fine looks like out of cinder. After the molding process after quenching in order to achieve the appropriate hardness and elasticity. Finally after 6 chrome. The general people could operate the PDR tool? This problem is indeed a problem. My personally think (do not represent the views of the majority).Depression repairing belongs to do the job by hands full. So ,what people could finish this job ?Who likes repair work, who likes use their hands to do job ,who engages in sheet metal working ,A person who with patience. Car paint and iron adhesion is strong, when the original the primary vehicle lacquer from factory is not split leather or a loss. The depression which couldn't be repaired is called putty wagon which couldn't be repaired, the vertical beam angle in car's side door also could not be repaired .Depression repairing and sheet metal repair is very good friend.
10. Depression repairing, Depression has its size, Depression and depression are able to be repaired .The central part of the edge of depression or depression die edge or a hard object impact die concave this depression after repair is not reached 100% ,so you must pay attention to it .
1 If you can use big tool, don’t use small tool, if you can use larger tool, don’t use litter, from bigger to smaller, from the shorter to longer. PDR tool's fulcrum is very important, it can try to chain fulcrum that is good force, not all that gap is relatively narrow point as far as possible in front (the hook turn as a fulcrum) when do sag with by hand movements are rotary tools. Handle tool heads top concave bottom and find the good fulcrum is equal to use the Leverage. In some places the fulcrum cannot find a repair special effort the general is a tire as a fulcrum hand to seize the tools back below is the tire wheel eyebrow repair your depression. The car door repair depends on the concave part of the dent. If the upper half of that is about to use glass as a fulcrum, someone asked. The glass will be broken? Please rest assured that the glass is strong not bad of course the outside of the glass to cushion the glass protecting plate, the tools how to get in? There is a wooden wedge toolbox end by a flat head is inserted the glass protecting plate and the outer metal strips in the middle hand gently down pat or fists hammer open one about 10 mm gap. Please doesn’t worry about this gap can not restore? As long as you take the wooden wedge off immediately after the restoration to the original state, car door's dent in the lower part, tool into the position is in the kind of mouth water. You look carefully and you will find it. After you have the depression repair tool, you must have confidence; otherwise you will not buy this thing. Just bought it is ready to do this job. You just know a little about this tool, first you think is very simple, the results it is not that what you want, maybe regret it, you think you shouldn't do it like this. After all, this is only a few people.
2 You bought this tool, you cost your money., don’t say this tool is bad .You should know how to use it .You should find a car front engine cover, and then welding a shelf, shelf around less than the engine cover (machine lid) don't too much small 10-20 Centimeters is ok, appropriate shelf at the height of 1 meters, because in learning sag repair without pain is not suitable for drawing leg acid, you can get the manual from me. Depression repairing lamp placement is very important and the height of the lamp is usually stay shave about 30 cm, the distance from the depression (far) 50-80 cm is appropriate, the lamp placed vertically and a downward adjustment of about 45 degrees, eyes' sight location is being repaired the plane light. Light - top shell at tube dark, you will feel very uncomfortable by eyes looked straight tube of the reflected light. eyes are easy to be astringent and fatigue .eyes’ sight position is parallel with your body's being repaired the plane, tube direct light (lamp) in the concave in the front of the lamp emitting light, just in the upper part of the depression, if you haven't understand it , don't worry about it ,there are drawings for you. The sag repair lights also called leveling lamp
3 The repair practice is very important in the early stages, you can't use it when you get it .Maybe the master of sheet metal may have to ponder for a part time, and you should do the repair practice again and again. You should think more about it know more about it, study it by your smart head.
4 1 As usual , if you study it carefully ,you can repair a dent which about 5 cm perfectly .So you should do the repair practice 3 or 4 hours a day
5 The main purpose of training exercises is (find points), what is the point. In (you have prepared and shelf fixed up the machine cover) in the above point 3-4 points by a carbon pen .Tool with a diameter of 10 mm, length of about 80 cm with a sharp tool, to find a fulcrum hanging on a chain below. With the left hand chain With the left hand chain tools into chain buckle (left hand the chain and the tool bar to prevent displacement or off) fulcrum position with a tip in the tool 1/3, so that the right hand's pressure on the tool is saving, fulcrum near the handle so close no leverage on the pressure, The right hand pressing tool handles,. You will find the height adjustment & tube direct light will become narrower, Observe carefully and you will see the specific location of the top of the tool, find that whether you touch these points. Maybe first one is failed ,second is failed too, maybe you failed all a day .But don't worry about it ,you should continue to do it .when adaptation of your eyes is very important .when you can see the specific location which you want to touch it .You can do everything which you want . You should not to see machine cover the following tools in what position by your eyes, if you see it, it is not so good for you. For example, depression repairing as we chat to play the keyboard, without looking at the keyboard and we will know the play which letter and it is very skilled. Dent repair needs a process like this Study depression repairing is more boring, in practice when daylight lamp cold iron and it is not an interesting thing. But it is easy to study than study computer typing.
6 Ha-ha. All make fun of for example. Have the courage? Dare to try? Tool investment cost? Depression repairing is only provided to the patient has the ability to have the brains of people. Please note that the white-collar and above class of people I'd advise you to avoid the bar. You think if you get a set of tools, and now this industry is a new industry, into a permanent benefit, tool lossless and environmental protection, it is a good project; more questions more drawings waiting for your call.
2013 excellent version PDR tool set packaging list
The lever tool 29 pieces, including big tools 17 pieces , hand tools (small tool) 12 pieces
A set of professional lights for dent repair
2 Leveling pens,
A glass plate,
A wood wedge,
A repair agent,
A 3M sandpaper ,
A Chain ,
Balanced bridge (adhesive)a set of depression repairing device (containing special Screw type plate 3 pieces) containing special &black glue stick 10 pcs,
Pull&knock type depression repairing device (including pull down an adhesive disc 30pcs, glue stick 10pcs, a hot-air gun),
Learning a CD-ROM, aluminum edge of exquisite packaging box a. The total number of 116 tools, can enlarge its own investigation.
- Unit Type:
- Package Weight:
- 25.000kg (55.12lb.)
- Package Size:
- 140cm x 30cm x 30cm (55.12in x 11.81in x 11.81in)
- Unit Type:
- Package Weight:
- 25.000kg (55.12lb.)
- Package Size:
- 140cm x 30cm x 30cm (55.12in x 11.81in x 11.81in)
- Bank Transfer
More tool pouch hand tools Products
From This Seller
From Other Seller
10pcs Maintenance supplies power h...US $5.61 / lot
28/PCS Hard drive head replacement...US $256.49 / piece
2013 Dent repair tool PDR Paintles...US $880.00 / piece
10piece suit of piano tuning repai...US $69.99 / piece
32 piece suit of piano tuning repa...US $330.00 / piece
High-quality Chrome vanadium steel...US $447.30 / set
Soldering station lead-free solder...US $8.00 / piece
BESTIR 2/3-Jaw Gear Puller Size 4...US $15.04 / set
Flaring Tool(VT04015) Car Repair T...US $11.72 / piece
common rail injectors repair toolsUS $458.59 / piece
Factory cost price promotion test ...US $190.00 / lot
35Piecs,used in repair workshop,Sp...US $455.00 / piece