Automatic Photoelectric sensor switch MODEL E for water pump relay, contactor, triggers

Product Description

Photoelectric sensor switch / pump pressure switch, booster pumps / submersible pump / priming pump / pump automatic control

The new intelligent pressure switch (special edition of the household water pump.) Interface 4 exceptionally thread interface; pressure 0-4Kg,0-6Kg,0-10Kg pressure based on actual choose style.

Model A, Model B, Model C, for direct control of the pump motor photoelectric pressure switch;

Model D, Model E, 220V AC relay, contactor, triggers, use photoelectric pressure switch!

MODEL A : 0-4KG

MODEL B : 0-6KG

MODEL C: 0-10KG

MODEL A: 0-4KG FOR PUMP WITH lift 0-35 meter

MODEL B: 0-6KG FOR PUMP WITH lift 0-50 meter

MODEL C: 0-10KG FOR PUMP WITH lift 0-85 meter

 MODEL D: 0-6KG for Contactors, relays, flip-flop

 MODEL D: 0-10KG for Contactors, relays, flip-flop

MODEL D : 0-6KG FOR PUMP WITH lift 0-55 meter

MODEL E: 0-10KG FOR PUMP WITH lift 0-85 meter

The product interface is 4“inch thread, 220V 50HZ, power ≤ 1.5KW Product Model: A section 0-4KG Model B,  0-6KG, Model C of 0-10KG; D of 0-6KG relay type, Model E, 0-10KG relay type, When purchase, please select the desired models.(Power ≤ 1.5KW pump can directly select the A and B or C models, big power can choose D, E,  control relay)

Product performance:

Free to adjust the upper limit (pressure limit is reached the pressure to stop) and lower (pressure less than the lower limit of pressure to start) the size of the pressure;
2, in the case of pipeline drip can effectively prevent the frequent starting of the pump;
3, pressure tanks do not need to install, comes with the pressure buffering function, small size, more beautiful;
4, controllable power, is currently available for 220V, 1.5KW direct control of the following power pumps;
Controllable pressure range 0-4KG,0-6KG,0-10KG;

6, the maximum fluid temperature: 80 degrees

7, the pressure gauge and pressure switch combined with one pointer to display real-time pressure;

8, can be used for the lower limit of pressure on a small range of pump use, for example, 1KG start 1.8KG stop;
9, long-term use of energy saving effect is obvious;
10, long life, can be used continuously for more than 140,000 times;
11, the control state stability, the stability of the start and stop control;
12, the waterproof performance is superior to achieve the specified standards of IP65 (water proof, pressure switch can not be placed on water use).

Function Description:

1, can be free to set lower limit pressure control point, and can be precise control;
2, the conventional environment of the household water pump do not need to install a pressure tank;
3, the design of the buffer movement can effectively prevent the frequent start of the pump, motor protection;
4, very stable, and more traditional pressure switch, there is almost no failure situation;
, Dustproof and waterproof performance is superior, as IP65 specified standards, to eliminate the phenomenon of leakage caused due to moisture like a mechanical switch;
6, the electronic circuit control, long service life;
7, the case of non-pressure tanks and stability control without frequent start, better with the pressure tank;
8, can be applied to a lot of harsh installation conditions, for example, low pressure pump control (requires professional installation), automatic control of submersible pumps;
9, can be accurately observed by the front table of the pressure controller pump working state, can detect pipe is leaking, the pump is blocked.
10, a photoelectric control, there is no frequent ignition to start and stop the phenomenon of traditional mechanical pressure switch contact contact to protect the pump to extend pump life.