China Post Free Shipping! Black Cover GSM Home Alarm system SMS sending and Remote control GSM-007m(850/900/1800/1900MHZ)

Product Description

China Post Free Shipping! GSM SMS Controller( 2 Inputs / 2 Outputs / USB Port ) RTU22 US$ 104.84/piece

DHL Free Shipping, GSM sms remote control system(S150)(8 Input / 2 Output ) RTU82 US$ 133.11/piece

China Post Free Shipping! 2012 NEW BLACK COVER wireless GSM Home Alarm system GSM-007M(900/1800MHZ) US$ 54.80/piece

GSM Based Wireless SMS Control Gate Door Opener(1 Output / 2 Inputs ) RTU5015 US$ 76.40/piece

China Post Free Shipping GSM Senior Guardian for Ederly Protection and Medical Alarm, Emergency Help with SOS Button B10 US$ 104.16/piece

Wireless Home Burglar Alarm Sysytem, Home Security Alarm System 007M3 US$ 41.38/piece

China Post Free Shipping! Wireless Outdoor Siren competiable with any alarm system with wireless transmitter 433/315mhz US$ 42.00/piece

China Post Free Shipping, 4pcs/lot Wireless PIR Motion Sensor Passive Infrared Detector US$ 33.68/lot 4 pieces / lot

home burglar alarm sysytem, home Security alarm system(GSM-007M) ,GSM-007M Home Alarm system with wireless Keypad & SMS Control. auto-dialing 5 persons.7 wire zones, 99 wireless zones.

Installation guide:

1. Insert SIM in alarm unit.

Put the SIM card carefully into the tray, and make sure the metal contacts of the SIM to be down.

Note: Before inserting SIM card into alarm unit, using a regular mobile phone to do the following steps:

- Set PIN code request to off.

- Delete all stored numbers.

2. Connect the antenna.

3. Insert the power supply.

a Connect the host with the adaptor. The host need 9V-12V DC, must be over 1000mA current.

b After 20 seconds, the signal status LED will turn to orange, and begin to flash, indicating system is checking SIM card and search for GSM network;

c After main unit finish checking the host, if the signal status LED turns to green and flashes slowly, it shows alarm phone number have been saved in the host, and the host is in arm status. If the signal status LED keeps on in green, it shows phone numbers have not been saved in the host, and the host is in disarm status.

4. Connect the siren to alarm system.

5. Connect wired sensors.

6. Connecting switched output devices (Home-appliance Control)

How to use remote controllers?

How to setup the alarm phone numbers and SMS

1. You can send command to the host (Control panel) to setup 5 groups of alarm receiving phone numbers. The format is: Password #operation code#content #

123456#51#13907550001# to save first group alarm phone number into the host.

123456 ...

123456#55#13907550005# to save fifth group alarm phone number into the host.

1. Set monitoring center phone number. The format is:

Password #71#monitoring center phone number #ID Number#

After this command was sent, the host will dial the monitoring center phone number when there is an alarm, and will show its ID Number in the monitoring center. For example, you can send: 123456#71#88886666#0001#. It shows the monitoring center number is: 88886666; user’s ID number is: 0001

Note: The monitoring center number should be no more than 15 digits; ID Number should be 4 digits. If there is no monitoring center, no need to set this command.

1. There are 7 kinds of alarm messages in the host: The first five messages are for wireless detectors of zone 1-5; the sixth message is for wireless detectors of zone 6-16; the seventh message is for wired port I1, I2, I3.

If the first wireless detector is triggered, the alarm message is: Wireless Activated (01)

.......

If the sixth to sixteen wireless detector is triggered, the alarm message is: Wireless Activated (i); i=6-16

If the wired detector is triggered, the alarm message is: Wired Activated (i); i=1-3, for port 1 to 3 alarm

4. Users can send commands to the host to change the alarm content. The alarm message cannot be more than 24 letters.

123456#81#Front door open# to save first group message into the host when first wireless detector is triggered

123456#82#Middle door open# to save the 2^nd SMS into the host when the 2^nd wireless detector is triggered.

GSM Alarm system (control unit) – 1 pc.

Wireless PIR detector – 1 pc.

Wireless door (gap) sensor – 1 pc.

Remote controller – 2 pcs.

GSM Antenna – 1pc.

Mini wired siren 110dB/0.3m – 1 pc.

Power supply (adapter) – 1pc.

Installation/user manual – 1pc.