Flycolor ESC 80A for brushless motor,rc aircraft,rc model+Program card + Free shipping

Product Description

 Application of the programming card 

Model airplane (including fixed wing, helicopter)

Model cars (including model vehicles, race cars)

Model ships

Electrical performance parameters of the programmed card: 

It can be directly connected to the programmable BESC, pay attention to the order of the tri-polar"+","-"and" P”. It can  

be used for both BESC and OPTO ESC.

Shape and weight of the programming card 

Shape: Round

Diameter: 60mm

Thickness: 5mm

Weight: 10G (with packaging)

Color: See the above picture

Usage of the programming card: 

IT IS VERY EASY TO USE. First set all the function’s with the jumpers, that you want the BESC to do on the programming card. THEN, Step(1), Connect the motor to the BESC, Step(2), connect the battery to the BESC. Step (3), Plug the signal and power wire that would normally go to your receiver from your ESC ( black, red and white), onto the program card where it shows the (- + P) pins. When you put this lead on the program card you will hear ONE “beep ” sound, this indicates that your SBEC has now been programmed successfully, according to what you have set the card to do.

When programming an OPTO ESC, do Steps 1 and 3, and do NOT do Step 2. Do Step (4), Use a battery of 4,8v to 6v and plug it onto the program card where it shows the + - jumper pins. You again will hear the “beep” sound indicating that the OPTO ESC has been successfully programmed. If you do not hear the one “beep” sound on both the BESC or the OPTO ESC to indicate that it is now programmed, you will need to do it again.

Standard configuration: 

Battery: Lithium-Ion battery

Start: soft start

Brake: no Brake

Low-voltage protection: lower power

Low-voltage protection point: 2.8V/50%

Steering: Anti-Steering

Timing setting: automatically

Application of ESC: 

Model airplane (including fixed wing, helicopter), model cars (including model vehicles, race cars), model ships, ndustrial products (including equipment, tools), ESC for medical products (including treatment, health care equipment)

Electrical performance parameters of ESC:

Input Voltage: 2-6LiPo batteries / 5-18 NiMh batteries 

Continuous current output: 80A

The maximum allowable instantaneous current (10S): 100A

BEC type: SBEC/UBEC/OPTO

BEC output: 5.5V/4A (SBEC), 5.5V/1A-4A (UBEC), 5.5V/1A (OPTO)

Standard configuration: UBEC 5.5V/4A

Shape and weight of ESC:

Dimensions (Length*Width*Height): 67*32*23

Weight: 94G (with BEC), 89G (OPTO)

Positive and negative power wires: wire size12#; Material: Copper Silicone Wire; Color: + Red - Black; Length: 100 (mm)

UVW wire: wire size: 14 #; Material: Copper Silicone Wire; Color: U Red V Blue W Black; Length: 80 (mm)

Signal wire: wire size: 24#; Length: 280 (mm); Connector specification: 3pin DuPont terminal

Types suitable for T head:     Rubber head Specification: 3.5*12

Thrum heat shrinkable catheter specification: 4.5*20;         Color: Red, White, Black 

Heat sink specification: 29*40                                 Color: Silver

Electric heat shrinkable catheter tone specification: 35*80      Color: Red

Manufacturers’ standard specification

Parameter settings of ESC:

Brake Setting: On/Off, the default is off;

Setting for battery type: LiPo (lithium) or NiCd/ NiMh (nickel metal hydride / nickel at),the default is LiPo;

Low-voltage protection threshold setting: low / medium / high, the default is medium (3.0v/65%);

Motor timing setting (increase the efficiency and the start stability of the electronic governor): low/medium/high, the default is medium (3.0v/65%);

Accelerated startup setting (for precision gearboxes and helicopters): (provide the rapid accelerated startup with linear throttle response), the default is soft;

Helicopter mode (for helicopters), the default is off;

Motor steering (clockwise / counterclockwise): forward steering / reverse steering, the default is forward steering;

PWM operating frequency: 8 KHz/ 16KHz, the default is 8 KHz;

Low voltage protection modes (lower power or stop immediately): lower power / immediately stop, the default is lower power.

Standard configuration:

Power line length: 100 (mm)    UVW line length: 80(mm), no rubber head or T head     SBEC 5.5V/4A