Universal Hi-off-Lo Round Switch Seat Heater

Product Description

Universal Hi-off-Lo Round Switch Seat Heater

I am here to recommend you some seat heating product.

1 High-low switch heating product

(1)A light shows three colors

  Red lights means high temperature,green lights means middle temperature,yellow lights means low temperature.

(2)How to make the copilot’s seat heating when it is at high level.

  Turn the switch once,both of the front seats are heating,then the product can controll the temperature itself.

(3)How to stop heating the copilot’s seat.

  Put the switch at the middle level,3 seconds later,the copilot’s seat stop heating,so you can use the driver’s seat.

Overall,use One switch you can controll two seats,it is controlled by MICRO-CPU.

2 Membrane switch heating system

(1)Membrane switch

  There are two membrane switches,each of them controll one seat,and there are four levels.

(2)Lights show the level

  Press the switch one time the temperature is at a different level,and a light lights,red light means high,green light means middle,when red,green ,both lights means low.when you press the switch for the fourth time no light lights that means stop heating.

(3)Easy to install

  Just put the two switches at a proper place.

3 Five switches heating system(single/double seats)

(1)There are five levels represent temperature,from level 0 to level 5,from low to high.

(2)how to heat the copilot’s seat

  Put the switch at level 5,then the copilot’s seat is heating and it is controlled by the driver’s seat.

(3)how to stop heating both of the seats

Just turn the switch at level 0

Car heating pad is introduced:

The company high low-grade car heating system has single seat two-seater of whole vehicle quality in all 3 years, will give you the consignor of incidental guarantee card, according to the product quality assurance date.

Cool car seat heating system

The heating system - specifications 26CM * 480cm. (quality assurance 3 years)

Temperature control high middle-and-low grade switch - size diameter 1.9 CM. Discretion two gears + OFF documents (quality assurance 3 years)

Thermal probe - the first function: temperature reaches switch preset temperature automatic power saving power supply
The second function: automatic power &high circulation outdated protect heating body to prevent spontaneous combustion

The fuse and relays (quality assurance 3 years) --

Product installation instructions:

I am here to recommend you some seat heating product.

1 High-low switch heating product

(1)A light shows three colors

  Red lights means high temperature,green lights means middle temperature,yellow lights means low temperature.

(2)How to make the copilot’s seat heating when it is at high level.

  Turn the switch once,both of the front seats are heating,then the product can controll the temperature itself.

(3)How to stop heating the copilot’s seat.

  Put the switch at the middle level,3 seconds later,the copilot’s seat stop heating,so you can use the driver’s seat.

Overall,use One switch you can controll two seats,it is controlled by MICRO-CPU.

2 Membrane switch heating system

(1)Membrane switch

  There are two membrane switches,each of them controll one seat,and there are four levels.

(2)Lights show the level

  Press the switch one time the temperature is at a different level,and a light lights,red light means high,green light means middle,when red,green ,both lights means low.when you press the switch for the fourth time no light lights that means stop heating.

(3)Easy to install

  Just put the two switches at a proper place.

3 Five switches heating system(single/double seats)

(1)There are five levels represent temperature,from level 0 to level 5,from low to high.

(2)how to heat the copilot’s seat

  Put the switch at level 5,then the copilot’s seat is heating and it is controlled by the driver’s seat.

(3)how to stop heating both of the seats

Just turn the switch at level 0

The temperature of the three products is controlled by micro-cpu.It is high quality.It is small,the width is 1 inch ,height is 0.5 inch,length is 2 inch.These products meet the customers requirements in many countries

Carbon fiber heating pad:
1) Round switch(controller)
2)CE/E-mark and TS16949 certifications
3)Energy saving
4)High quality

Carbon fiber heating pad:

1.High quality and competitive price(Our products are on a par with international advanced products,but the prices are only one-fifth of similar foreign products.)

2.Could be developed and manufactured according to clients requirements.

3.The carbon fiber seat heater heates and controls the temperature automatically

4.Carbon fiber has the wavelength of infrared ray that is healthful to human body.

5.Easy to install

6.TS16949 certificate

7..TUV approval

8. Switches with autonomous intellectual property right

9.Use the advanced special equipment(the only one in Chinese)

10. The heating power will not be attenuated in the long run.

11. Connection terminal and housing: AMP series products

12. Thin film pressure sensor of human body: Owns autonomous intellectual property right;All products can be installed with such function

1 Composition

  Four heating pads,and a wire with a controller.

2 Installation

  (1)First,take off the suit of the seat,then put the pads on the back and bottom of the seat,make them durable.

  (2)Connect the plugins of the pads with the controller under the seat after the pads are ready.Connect the driver’s four-core pads to the controller,use a buckle to stabilize the controller under the seat.

  (3)Put the wire at the corner of the ground,connnect the switch first then connect the red line and black line and yellow line to the power supply.

  (4)Find a proper place between speaker and handbrake,make a hole,the diameter of the hole could not be bigger than the diameter of the switch,if not the may be not stable,you can put some glue in the hole to make it stable.If there is already a hole on the car,you can take off the cover of the switch and make the size of the hole fit the switch then put the switch in the hole.

  (5)After the switch is ready,connect the switch to the four core plug-ins of the wire.

  (6)You can connect to the power supply now.First,connect the black line to the ground line,if there is a screw nut on the car and there is paint on it,you should cut off the paint first then connect the black line under the nut,it will be poor contact if you do not cut off the paint.Then you can connnect the red line,find a line which can transmit at least 10A current under the dashboard,when the car is not working there should be no current,you can also connect to the fuse which can transmit at least 10A current and the diameter is at least 1.5mm.How to find the line,use a multimeter to test,when the car is working there should be at least 12V,when the car is not working there should be no voltage.Connect the yellow line to the On-line.Connect the yellow line to the ON-line,make it stable.

  (7)Some point to pay attention:the carbon fiber in the pads should not meet the metal part,you can use mackintosh to separate them.

3 How to use

  (1)There are five levels of the switch:51 degrees celsius(123.8 Fahrenheit) 47 degrees celsius(116.6 Fahrenheit) 43 degrees celsius(109.4 Fahrenheit) 40 degrees celsius(104 Fahrenheit) 36 degrees celsius(96.8 Fahrenheit).

  (2)One switch could controll two seats.

  (3)If there is only one person in the car,then only the driver's is working.Press one time the red light is up,press the second time the yellow light is up,for the third time the green light is up,for the fourth time the red light is flashing,for the fifth time the green light flashing,for the sixth time it will be turned off and the light is off.These six level means six temperature,from high to low.When you are first time to start the car in the morning,press the button once,the red light is up means the higheas level,if you feel it is too hot you can choose a proper level.

  (4)If you want the two seats working just press the button for three seconds,the yellow light will flash for couple times,that means the co-pilot's seat is start to heat too,the temperature is the same with the driver's seat.If someone is midway aboard,just press the button for three seconds,the yellow light flash for couple times,then the co-pilot's seat start to heat and it will find a proper temperature.Nomatter whether there is some at the co-pilot's seat just press the button for three seconds the seat will start to work.

  (5)There are two way to turn it off.First,just stop the car.If only the driver's seat is working put the level at when the green light is flashing then press one more time it will stop heating.Second press the button for three seconds.

4 his product is easy to install,easy to use,could controll two seats by one controller and have five levels.

Fever piece is introduced:
This product can according to the customer request product size and temperature and so on production, voltage can be producing 1.5 V - volt.
USB carbon fiber fever slice particularly recommended for wrist has inflammation, mouse hand need hot compress friends, it than titanium circle effective, convenient than pouchof hot water

USB shoes heating pad

Clothing heating pad

The mouse pad heating pad

Car cushion heating pad

Sofa heating pad and 24 v converter

Far infrared health care mattress + 24 v converter