GSM alarm with Voice speaker (GSM-M3A2)

Product Description

GSM home alarm with PIR, Door contact

NOTE: Quad band for the whole world, esp.for South American countires.

1.Two-way to communication.
2. Eight wireless LED defense zone, four wired defense zone
3. The system supports the GSM cell phones, no need the fixed telephone line.
4. Can set HOME arm/AWAY arm
5. When alarming, system plays the recorded voice at first, call six phone numbers and send the short message (SMS)
6. The SMS (no longer than 160 characters or numbers) can be programmed by users
7. Record 10 seconds message
8. Using remote controllers, you can arm, disarm, panic from long distance.
9. Can control the system by using a telephone or cell phone anytime, wherever you are. For security reasons, a PIN code must be used for access.  
10.Can support all kinds of wireless sensors, such as PIR detectors, door (gap) sensors, gas sensors, smoke sensors, beams, panic buttons and so on, 160pcs in total.
11.Send the SMS to GSM alarm system to program, it is very easy and quick to be installed and operated
12. With inner back-up battery, when the power is off, it still can work about 12 hours.
13. With output relay, can control the home appliance, like light, cooker and so on
 
Technical parameter:
Operating voltage: Input 100-250V, output 12V.
Wireless receiving distance: >100m
Operating Frequency:  433 MHZ, 850/900/1800/1900MHZ

II . Before installation, please pay attention:

When using GSM main panel, it is better to put up the antenna to have strong signal, to guarantee the distance between main panel and detectors

Dont put the GSM main panel near the computer, TV, fax, microwave and other high power machine, they will disturb the GSM system.

Dont put water on main panel, detector and sensor.

Wireless PIR detector, install it to be 2-2.2M, it is better not to face the window or door.

Read this manual carefully before using, to avoid having faulty alarm or no alarm.

III. Operation:

To input the SIM card

Press the yellow point by pen or other tools on the main panel, the SIM card box will come out, put the SIM card carefully into the box, and make sure the metal side of SIM card to be down.

To start the operation

Firstly make sure that the SIM card has the money, input the SIM card GSM alarms SIM box carefully, and connect the antenna first, then connect the DC adaptor and press the ON/OFF, you will see the power LED is on, in 30 seconds, it will find the GSM network. When finding the network, the power LED on the main panel will glitter in 5 seconds. If it glitters in one second, it doesnt find the network.

1. How to code/register the wireless detector?

Press the CODE button on the main panel without stop for about two seconds, until the first defense zone LED is red, with one beep, you can press the RECORD button quickly to change the defense zone according to you, then trigger the wireless detector and sensor (press any button on remote controller, make PIR and door gap sensors to work, or let the smoke/gas detector send signal), they will be recognized and coded into the defense zone.

2. How to trigger the wireless detector when code/register?

Before coding/registering, please collect all detectors and make sure their battery inside and can work normally. When the defense zone LED is red, now you can start to code/register them. For example, door sensor, just remove the two parts of door sensor and remove back. And for PIR Sensors, you can turn the switch to on, then turn it to off to avoid wrong alarm. For remote controllers, you can press any button, it will send the signal. For gas detectors, there is a black switch on the left side; you can press it to register it with GSM alarm. For smoke detector, there is crystal point for testing, press the point without stop, it will have big sound and send signal to the GSM alarm.

3. How to return from the code/register condition?

When on the code/register condition, press the CODE and quit quickly on the main panel, with one beep to show successfully. If there is no operation in 30 seconds during code/register condition, it will return automatically.

4. How to delete the wireless detector ?

If you want to delete the second defense zones, Press the CODE on the main panel without stop for about one second, until the first defense zone LED is red, with a beep, press RECORD and quit quickly on the main panel to change to the second defense zone , then press the RECORD again for long time on the main panel, until the second defense zone LED dont glitter, it is ok to delete the second defense zones detector now.