Automatic cup sealing machine,cup sealer
Voltage : 220VAC
Max. Sealing size: 95mm
Max.sealing height: 15mm
size: 540 × 270 × 720 mm
The film material and sealing temperature description:
1, PE (polyethylene): 170
2, PP (polypropylene): 170 to 200
3, PS (polystyrene): 180
4, easy to tear film: 120 ~ 180
5, PET (polyester): 160 to 200
A) sealing film
1. Get the film need to confirm the direction of the film winding identify counterclockwise, and on the film pole fixed. (Turn off the power when the wear film)
2. Note that the film before and after the splints and film closely integrated, such as not closely integrated, the need to use a utility knife to cut the film the inside of the paper tube bevel and then rows into.
3. With plastic sheets to put on film, the film is firmly attached to the receipt paper tube.
(B) sealing steps (panel instructions)
1. Power, turn on the power switch, indicator lights, the thermostat is set to a predetermined temperature, light green heating. When on a hot plate to a predetermined temperature, the red thermostat indicator light (sealing machine work, electric device in the heating and insulation state constantly alternating, so the green and red lights constantly alternate display, this is a normal phenomenon).
2. The plastic cup into the lower die skateboard, hand the lower die skateboard push to determine the location of touch after the trip switch on the mode received signal will automatically under pressure sealing, automatic rise reset, touched on the trip switch on mode motor stops. laminate motor begins to turn, turned a predetermined length, the motor stops automatically control by electric eye film.
3. Film motor rotation before they pull the lower die skateboard pushed into the plastic cup into the lower die skateboards, the next cycle begins.
A properly grounded to ensure the safe use of electricity.
2, when a machine fails, you should turn off the power to restore the normal temperature before troubleshooting.
3, the use of the process may not handle stretching between the upper and lower mold, so as not to crush or burns.
Upload Cup push mode movement, must be on the die to the highest point of the stop motion.
1, the template contains cup onto the innermost is not allowed rebound, or the upper and lower mold will be damaged. 2, the operating voltage must be maintained at 220V ± 5%.
, Regularly clean the surface of the machine, the floor and the lower die skateboard, trench, mold platen and positioning rod (Note: You must turn off the power and restore the normal temperature).
The lower die skateboard, trench, rail, and other transmission parts regularly add butter to ensure the use of the machine
Cleaning cutter approach: first the lower die with a cotton ball scuppers plugged, the water into the lower die groove, until the filling, and then push the lower die skateboard in place, under the pressure of the upper die pressure to the lowest point, soak for a few minutes to clean up to the cutter. Repeated several times.
@.Items will be sent out within 3 days after the payment cleared.
@.Combine Shipping Discount Available for purchasing more than 2 items. Buy more save more!
@.All items will be shipped according to the addresses you left, please make sure the addresses is correct. If the address registered is not correct, please send us your post addresses by e-mail ASAP or the buyer will be responsible for the full refund.
@.All orders will be scheduled to ship out immediately after we receive your full payment. We almost ship the item(s) to all over the world; we ship the item(s) to the following countries directly by EMS, DHL or TNT, Hong Kong, Macao, Japan, Korea, Malaysia, Singapore, USA, Canada, Australia. It will take about 5 to 7 days to reach you. For the little item, it may be shipped as Air Package, and it need about 2-3 weeks to reach you!
@.If you are living in the following countries please contact us first to confirm the postage.
Bahrain, Iraq, Uganda, Jordan, Israel, Oman, Qatar, Kuwait, Iran, Madagascar, Syria, Côte d'Ivoire, Djibouti,
Senegal, Kenya, Tunisia, United Arab Emirates, Cyprus, Egypt, Ethiopia, Gabon, Ghana, Guinea, Niger,
Nigeria, Hungary, Poland, Cayman Islands, Czech Republic, Russia, Latvia, Kazakhstan, Belarus, Romania,
Slovakia, Estonia, Ukraine, Yugoslavia, North Korea, Iceland, Saipan, Guam, Tonga, Albania, Bulgaria, etc.
@.Please Contact us ASAP if you can't get it/them on time or any other questions you have.
@.All items are inspected for damage or defects prior to leaving our warehouse. Contact us immediately if shipping damage is discovered.
Serious bidders only, please. Orders will be cancelled and an unpaid item dispute filed if payment is not received within 10 days of purchase.
The item is guaranteed to be as Described! If, for any reason, you are not satisfied with your purchase, you may return the item (in good condition though) within 60 days, we'll be happy to make an exchange or issue a prompt and courteous refund. Please note: Sorry, we do not return or reimburse shipping charges!
a). Gorgeous machinery is a professional supplier of packing machine in China. All our products are from factory directly. This is why we can keep our price competitive.
b). If you are interested in any item about packing, contact us please! Our email is available on the work days from Monday to Sunday. We will give you a quick reply as soon as we received your emails.
Feedback 100% custom satisfaction is our goal.
Please give us a five star feedback if you are satisfied with our products and service. Please contact us if you are not fully satisfied, we will give you full refunds.