1.the electric tool set is a new generation of automobile crane, the tyre disassembly tool, the electric jack tool has completely changed the traditional design pattern of jack. It makes use of the power car cigarette lighter, only need to gently press the remote control switch can easily lift the roof, the tool set is safe and reliable, reasonable structure, rigorous process, easy operation etc..
2.convenient and quick operation:
Electric jack using built-in 12V DC motor, through the infrared remote control the motor free uniform and stable lifting, bottom slab bearing design, saving time and labor, to avoid the traditional jack operation danger, convenient and safe.
Adjustable height range, applicable to all kinds of small vehicles.
Electric wrench with 4 different sizes of sleeve, can be in 3 seconds easily remove or tighten various kinds of car wheels setscrew 1.
Electromotive spanner equipped with loose / tight switch, compact and convenient operation safety.
3.take electricity convenient: equipped with battery clamp and a cigarette lighter plug, can be directly inserted into the cigarette lighter, or is connected to the vehicle battery can be used, the length of about 4.5 meters.
4.security: protection device of electric jack with a lifting self-locking, when exceeding the lift range will automatically stop lifting, safe and reliable.
5.environmental clean: using screw gear transmission, discard the traditional hydraulic design, working environment clean.
6.easy to carry: packaging with hollow blow molding tool box.
The use of voltage: cigarette lighter power DC12V or car battery power
Working current: less than 10A
Weight: 2000KG (applicable to 2 tons or 2 tons of the following car)
Lifting range: 12CM to 35CM
The use of temperature: -40 to +70 degrees Celsius
Plastic box size: 45*30*12.5CM
1.a battery clamp
2.the cigarette lighter plug connection 1 (3.5 m)
3.the fuse (10A) 3
4.the crank handle a
5.double sleeve 17-19, 21-23 each one
6.a lever handle
7.a user manual
When in use, the jack on level ground, and to ensure that no foreign body jack bottom.
[Using the method of electric jack]
1. the car park to the level road, the engine flameout, also don't forget to pull the hand brake.
2. the electric jack is arranged in for steel beam under near tyre body, and the top cap of electric jack alignment body below the support point, so that the electric jack can be safe, effective lifting.
3. through the following two ways to connect to the 12V power supply electric jack:
A.The use of lighter connection: end of the cigarette lighter plug wire inserted into the cigarette lighter socket, plug the other end of the 5.5mm to insert the 5.5mm plug socket on the electric jack. (Note: the fuse rated current cigarette lighter and not less than 10A)
B.The use of the vehicle battery is directly connected to the end of the line: a cigarette lighter plug inserted into the cigarette lighter socket with the battery clamp one end, while the other end red clamp battery "+ battery clamp" (positive), black clip and battery "-" (negative electrode) is connected, and then plug the other end of the line. 5.5mm plug into the electric jack 5.5mm plug seat.
4. the use of operation: in determining the first few steps done, you can start jacking operation. Hold the remote control, according to the need, press the button on the remote control, "+" said rising, "_" down, "0" said stop.)
5. in the lifting process, should earnestly observe lifting dynamic, ensuring the electric jack did not tilt, until the wheels and the ground to leave 20mm, the wheels can turn freely should stop jacking, replacement of tires.
[Using the method of electric wrench]
1. when replacing the wheel off the ground, the electric wrench connected power supply (electric wrench on the 5.5mm power supply plug directly inserted into the cigarette lighter plug one end of the 5.5mm plug seat).
2. The choose the appropriate, square head square hole is sleeved in the top of the electric wrench, loosen or tighten bolts.
3. according to the required direction, choose loose, tight switch. The power switch left mark "" ", is the reverse direction, the symbol" - ", is a clockwise direction, intermediate markers", is to stop. Press and hold the corresponding direction switch with the thumb, hear "click, click" 1-2 crash to loosen the thumb, the whole process about 2-3 seconds.