Thermostatic shower faucets,temperature showers faucet,mixer valve,Induction tap ,Bathroom Sense Faucets sets ,free shipping

Product Description

Technical Performance Parameter:
1) Workable Water Pressure: 0.05-1Mpa
2) Perfect Water Pressure: 0.05-0.5Mpa (Exceeding 0.5Mpa recommend to install controlling of flow rate equipment)
3) Scope of Cold Water Temperature: 5-29oC
4) Scope of Hot Water Temperature: 50-80oC
5) Scope of Adjustable Temperature: 20-50oC
6) Safety Temperature Stop: 38oC
7) Result of Unavailable Cold Water: When cold water unavailable for more than 5 seconds, valve will control water flowing rate to 1.9Litre/Minute, volume of flowing water ≤150ml, temperature of water≤49oC
8) Life of Valve: CSA B125-98 ASSE 1016 (more than 100,000 Cycles)

Take you to visit our pr oduction base:
Our sample room

We use copper materials

Delivery area corner

General Faucet Installation Instruction
Step 1: Position the Faucet

Step 2: Attach the Water Supply Tubes

Step 3: Connect the Faucet Lift Rod

Step 4: Flush the Faucet

• Anytime you work on plumbing, filings, chips, and other debris can fall into the plumbing pipes.
• This debris can damage the sealing surfaces inside the faucet and cause leaks.
• Remove aerator and black sealing gasket above it.
• Before turning on the water supply, make sure the faucet handles are open (on position) in order to remove the debris without causing damage. (Diagram A)
• Open both water supply valves under the sink. (Diagram B)
• Allow the water to run for 15 seconds. (Diagram C)
• Close the faucet handles (turn off).
• Make sure any debris is cleaned from the aerator screen. (Diagram D)
• Replace the aerator. (Diagram E)

• From the top of the sink, insert the lift-rod into the faucet. (Diagram A)
• From under the sink, make sure the pivot-rod is in the down position. Insert the lift-rod into the lift-rod strap. Tighten the screw.
• From the top of the sink, make sure the lift-rod opens and closes the drain plug as desired. (Diagram B)
• Make any needed adjustments by loosening the lift-rod strap screw and repositioning the lift-rod.
• If you need to connect the lift-rod strap to the pivot rod, slide one end of the spring clip onto the pivot-rod.
• Make sure that both the pivot -rod and the lift-rod are in the down position. Insert the pivot-rod in the closest hole in the lift-rod strap.
• Slide the other end of the pivot-rod. Make sure the lift-rod opens and closes the drain plug as desired.
• Make minor adjustments by loosening the lift-rod strap screw and repositioning the lift-rod. (Diagram C)
• Make major adjustments by removing the spring clip and moving the pivot-rod to a different hole in the lift-rod strap.

• Water is typically supplied to the faucet through water-supply tubes.
• Wrap the threads of the water-supply valve with Teflon tape. Although most plumbers use only Teflon tape, some plumbing supply manufacturers also recommend using plumber’s putty. (Diagram A)
• Thread the water supply nut onto the shut-off valve. Tighten the nut with a wrench. (Diagram B)
• Wrap the threads on the faucet shank with Teflon tape, and then thread the water supply nut onto the faucet shank. (Diagram C)
• Tighten the nut with a basin wrench. (Diagram D)

• Begin installing your faucet by placing the gasket and faucet in position on the sink. (Diagram A)
• From under the sink, thread the plastic mounting nuts onto the faucet shanks. Be sure the large side of each plastic mounting nut is up. (Diagram B)
• From the top of the sink, check the faucet and gasket position. (Diagram C)
• From under the sink tighten the mounting nuts, making certain not to over-tighten which could damage the nuts and make them difficult to remove in the future. (Diagram D)